这篇文章将为大家详细讲解有关linux如何实现巡检，小编觉得挺实用的，因此分享给大家做个参考，希望大家阅读完这篇文章后可以有所收获。
核心代码：
#!/bin/bash
check_process(){
tolprocess=`ps auxf|grep DisplayMa[nager]|wc -l`
#if [ "$tolprocess" -lt "1" ];then
if [ "$tolprocess" -ge "1" ];then
echo 'process ok'
else
echo 'fail'
fi
}
check_log(){
if [ -e /etc/syslog-ng/syslog-ng.conf ];then
conlog=`cat '/etc/syslog-ng/syslog-ng.conf'|grep "10.70.72.253"|wc -l`
if [ "$conlog" -ge "1" ];then
echo 'syslog-ng ok'
fi
elif [ -e /etc/syslog.conf ];then
conlog=`cat '/etc/syslog.conf'|grep "10.70.72.253"|wc -l`
if [ "$conlog" -ge "1" ];then
echo 'syslog ok'
fi
else
echo 'log not find or error'
fi
}
check_cpuidle(){
mincpu=`sar -u 2 10|grep all|awk '{print $NF}'|sort -nr|tail -1`
if [ $(echo "${mincpu} < 20" | bc) = 1 ];then
#if [ "$mincpu" -le "20" ];then
echo 'cpu idle is less than 20% ,please check'
else
echo 'cpu idle is more than 20%, it is ok '
fi
}
check_mem(){
vmstat 2 10
}
check_disk(){
chkdsk=`fdisk -l|egrep 'failed|unsynced|unavailable'|wc -l`
if [ "$chkdsk" -ge "1" ];then
echo 'fdisk check ok '
else
echo 'fdisk check find error,please check your disk '
fi
}
check_io(){
util=`sar -d 2 10|egrep -v 'x86|^$|await'|awk '{print $NF}'|sort -nr|tail -1`
await=`sar -d 2 10|egrep -v 'x86|^$|await'|awk '{print $(NF-2)}'|sort -nr|tail -1`
if [ $(echo "${util} < 80" | bc) = 1 ] && [ $(echo "${await} < 100" | bc) = 1 ] ;then
echo 'disk io check is fine'
else
echo 'disk io use too high '
fi
}
check_swap(){
tolswap=`cat /proc/meminfo|grep SwapTotal|awk '{print $2}'`
#awk '/SwapTotal/{total=$2}/SwapFree/{free=$2}END{print (total-free)/1024}' /proc/meminfo
useswap=`awk '/SwapTotal/{total=$2}/SwapFree/{free=$2}END{print (total-free)}' /proc/meminfo `
util=`awk 'BEGIN{printf "%.1f\n",'$useswap'/'$tolswap'}'`
if [ $(echo "${util} < 0.3" | bc) = 1 ] || [ $(echo "${useswap} < 1024" | bc) = 1 ] ;then
echo 'swap use is ok '
else
echo "useswap: $useswap kb, swap util is $util"
fi
}
check_dmesg(){
chkdm=`dmesg |egrep 'scsi reset|file system full'|wc -l`
if [ "$chkdm" -ge "1" ];then
echo 'dmesg test ok '
else
echo 'dmesg check find error '
fi
}
check_boot(){
chkdm=`cat /var/log/boot.msg|egrep 'scsi reset|file system full'|wc -l`
if [ "$chkdm" -ge "1" ];then
echo 'boot check fine '
else
echo 'boot check find error '
fi
}
check_inode(){
maxinode=`df -i|awk '{print $5}'|egrep -v 'IUse|-' |sed 's/%//g'|sort -nr|head -1`
if [ $(echo "${maxinode} < 80" | bc) = 1 ];then
echo 'inode check ok '
else
echo 'inode used more than 80% '
fi
}
check_df(){
dfuse=`df -HT|awk '{print $6}'|grep -v Use|sed 's/%//g'|sort -nr|head -1`
if [ $(echo "${dfuse} < 80" | bc) = 1 ];then
echo 'disk used is less than 80% ,it is ok !'
elif [ $(echo "${dfuse} > 80" | bc) = 1 ] && [ $(echo "${dfuse} < 90" | bc) = 1 ];then
echo 'warning , disk used more than 80% and less than 90% '
else
echo ' Critical, disk used more than 90% '
fi
}
echo '################### check process ###################'
check_process
echo '################### check syslog ####################'
check_log
echo '################### check cpuidle ###################'
check_cpuidle
echo '################### echo memory stat ################'
check_mem
echo '################### check fdisk #####################'
check_disk
echo '################### check io used ###################'
check_io
echo '################### check swap used #################'
check_swap
echo '################### check dmesg #####################'
check_dmesg
echo '################### check inode #####################'
check_inode
echo '################### check disk used #################'
check_df保存为/system/check_linux.sh
关于“linux如何实现巡检”这篇文章就分享到这里了，希望以上内容可以对大家有一定的帮助，使各位可以学到更多知识，如果觉得文章不错，请把它分享出去让更多的人看到。
